Cracked marble slab

How to repair a broken marble slab

Marble is a popular rock that has been used since Roman times for sculpture, building, and furniture. In the Victorian era, Carrara marble was commonly used for tabletops and unfortunately is often broken by careless moving companies. A cracked marble slab, with sentimental value, can easily be repaired by the handy homeowner: What is Marble? ... Read more

By John

Marble is a popular rock that has been used since Roman times for sculpture, building, and furniture. In the Victorian era, Carrara marble was commonly used for tabletops and unfortunately is often broken by careless moving companies. A cracked marble slab, with sentimental value, can easily be repaired by the handy homeowner:

  1. Check the edges to make sure they are clean
  2. Using a grinder, cut biscuit grooves to strengthen the join
  3. Apply 2-part epoxy adhesive to both sides
  4. Balance the 2 halves, so that the glue can set up under gravity
  5. Fill the missing areas with tinted epoxy

What is Marble?

ANTIQUE marble tables
Antique tables with marble tops

Marble is a metamorphic rock resulting from the transformation of limestones under high pressures and temperatures. Typical marble is formed by interlocking coarse crystals of calcite (CaCO3) or dolomite (CaMg(CO3)2. The characteristic gray swirls are caused by mineral impurities such as iron oxide, clay, or silt.

Marble is a soft rock (Moh’s hardness 3.5 to 4) and is easily scratched. It is also attacked by acids and so can be pitted and marred by common household products like vinegar. For these reasons it is recommended that marble tabletops are coated with a stain-resistant sealer.

Marble is also brittle and is easily be broken due to careless handling (especially by moving companies). The break very often follows a previous crack or a natural weakness like a vein or fissure in the rock.

Artistry in Glass is an Amazon Associate – we earn a commission from qualifying purchases.

How to fix a cracked marble slab

If you break a modern marble slab forming part of a kitchen countertop, consider replacing it with a new top. However, with antique marble having sentimental value and, especially with custom shapes, it is well worth attempting a restoration. For best results, follow these steps:

Examine the edges

Old fill in vein
Broken edge with remnants of old adhesive

To ensure a strong glue joint it’s essential that the two broken edges are perfectly clean, free from dirt and grease, and from previous adhesives. If the crack occurs along a previous break it is highly likely that old adhesive will be present.

Different adhesives need different solvents for removal. In practice, a combination of dissolving and picking or cutting away the old glue with a chisel or Exacto knife is the best approach. Superglue (cyanoacrylates) dissolves in acetone and rubber cement needs a commercial paint stripper. Epoxies will loosen with heat but need a strong product like “Attack” Epoxy Adhesive Remover (available here on Amazon) for dissolving although “Goof Off” can sometimes be effective. In all cases, be sure to test an inconspicuous small area before proceeding and take care to read instructions, and follow safety precautions when using strong chemicals.

Optional “Biscuit” Jointing

Even with strong epoxy adhesive, considerable stress can be applied to the relatively small glued area of a 1″ thick marble slab, especially if the substrate is uneven. So, to make sure of a secure bond, Artistry in Glass has adapted the woodworkers’ biscuit joint technique to the gluing of marble slabs.

Making biscuit grooves
Optional step: using an angle grinder to cut “biscuit” slots in marble slab

Marble is soft (Moh’s hardness 3) and can easily be ground away using an angle grinder. Mark the two edges so that biscuit grooves correspond on opposite sides of the join. Be sure to wear goggles and a dust mask and also take great care not to chip the slab surface by cutting too close to the edges.

Biscuit Joints
Cross-section showing epoxy glue forming a biscuit joint

After cutting the biscuits, brush off all the dust and wipe down the surfaces with rubbing alcohol or acetone (these evaporate without residue), in preparation for gluing.

Balancing the Slab

Before applying the adhesive it’s very important to prepare a balancing situation because even using quick-setting (5-minute) epoxy, it is not possible to hold the two halves in place without arranging a support system.

Insider money-saving tip

It is almost impossible to line up a broken marble slab when it is laid flat. A counter-intuitive fact is that the best way is to support the two halves vertically.

Upright gluing position
Back and front views of the slab in the recommended gluing position

If the break is clean, the two halves should “key in” together to form a perfect fit. Our recommended gluing method is to use the force of gravity to hold the upper piece in position while the glue hardens. We secure the lower part with woodworker’s clamps as shown above.

Gluing the Slab

There is an enormous and confusing range of epoxy adhesives available these days and it is hard to figure out which is best. The main factors that govern your choice for the repair of china, pottery, marble, and rocks are the setup speed, the color, the strength, and the possible degree of yellowing with exposure to UV light. Finally, the cost may be an issue if you are using a large amount. For a marble slab, strength is the most important characteristic and we recommend an epoxy like JB Weld “Clear Weld” which has an advertised shear strength of 3900 lbs/sq in.

Making sure the edges of the marble are perfectly clean and dry, mix the epoxy, and apply generously to both sides. Normally, with a close-fitting join, for example on a china plate, we need a very thin layer of glue on just one side of the join – however, where we are using the biscuit joining technique we need to use sufficient glue to fill the biscuits.

Place the top piece in the position you have prepared and use tape if necessary to stabilize the join. Immediately wipe off any excess epoxy with alcohol – this will save considerable time scraping off dry glue later. Check the alignment and leave the pieces overnight to set up.


Filling the Crack

Even the cleanest break will have “micro chips” or small missing pieces that need to be filled. In our example, the break followed a previous fracture, a lot of material was missing, and a large amount of epoxy putty was needed.

marble crack with epoxy putty
Crack in marble slab ready for filling with epoxy putty

Just as is the case with adhesives, there are numerous choices for epoxy putty: these will be discussed in a future post. For this type of repair, requiring a significant amount of material, we like the “Epoxie Sculpt” brand. Choose from natural color mixes to a neutral grey or white – both can be tinted by the addition of dry pigments or rock dust to match the marble.

Tinting the epoxy putty
Ready to finesse the color of the epoxy slightly by mixing in a little yellow ochre

Mix the 2-part epoxy putty thoroughly and tint it with pigment (if you can’t easily find artists’ dry pigments you can use powder scraped from chalks or artist’s pastels).

Steel Chisel Sets for applying epoxy putty

Spatulas (also called steel chisel sets) are very useful for squidging the putty into cracks. Using a spatula, force the putty into the crack and smooth the surface as level and even as possible. The smoother you get the putty, the less you will have to sand off when it is hard. Leave the epoxy putty to set up overnight.


Sanding & Painting the Repair

When the epoxy is dry it is time to complete the restoration. First, sand down the high spots until the putty is level (be careful not to scratch the unbroken marble). Go down through the grits from #200 to #1000 until the putty is perfectly smooth. (It may be necessary to fill micro-holes in the crack with a second batch of putty or filler).

Painting marble
Painting epoxy putty to match marble

Then, use your favorite paints (acrylics are OK) to finesse the color of the epoxy by adding off-white and gray swirls as necessary to match the marble. You can have fun at this stage, feathering and shading the colors until the crack appears to disappear.

Varnishing the Marble

Even if you are successful in matching the colors, the crack will still be visible in bright light because of the difference in its reflectivity compared to the polished marble. The trick to completely disguise the crack is to apply a new sealing or varnishing treatment to give the surface a homogeneous appearance. You can apply a standard granite/marble sealer but a liquid of this type may react differently on the painted repair.

So, we recommend using a clear varnish from a spray can. These days, very high-quality aerosol varnishes, which are UV-resistant, and non-yellowing are available, in gloss, satin or matte finishes. (We like the high-quality Krylon, Colormaster brand), For most antique marble tops, a satin or semi-gloss varnish (like this available on Amazon) is normally the best.

Krylon K01323000 Gallery Series Artist and Clear Coatings Aerosol, 11-Ounce, Satin Finish Satin finish varnish will protect your antique marble


Taking Care of Your Repaired Marble

An antique marble slab, repaired as outlined in this post should not be used as a work surface. It is safer to keep it as a decorative part of your furniture. To maintain your marble, just dust it with care: do not use any abrasive cleaners, Comet, or Scotch pads. If the surface becomes marred you can sand it delicately with fine steel wool and re-seal with a penetrating sealer or satin varnish.

Protecting your Marble Slab

$150 off tabletop ad

Protect your marble with a glass tabletop

Glass can be an inexpensive way to protect your easily scratched, antique marble. If you are considering Solar Panels, check out our offer to save up to $150.00 when you buy a system from Solar Solution AZ.

Trust Artistry in Glass for your Tucson Repairs

Watch our informative video to see the range of restorations available at Artistry in Glass.


Unique Mirror Resources from Artistry in Glass

Mirror Installation & Removal

Mirror Repair & Restoration

Artistry in Glass: your source for antique repair in Tucson

Check out these informative articles:-

Glass safety – learn from the experts!


As an Amazon Associate, I earn from qualifying purchases.

Artistry in Glass Green Logo

(520) 320-0104

support@tucsoncrystalandchinarepair.com

Opening Hours

Wed - Thu 9.30 - 5.00

Friday ..... 9.30 - 4.00

Sat - Tue .... Closed

Copyright © Artistry in Glass Inc, 1999-2024

All rights reserved

Privacy Policy